How To Fix Broken HDMI Port? – Learn Here

Last Updated on December 23, 2020

You will save yourself a lot of hassle by knowing how to fix broken HDMI port. The amount of fixing depends on the extent of the damage as well as the device that the HDMI port is attached to. But with some precaution and skill, you can do this yourself.

You will first identify the damage that’s been done. How extensive it is. Then, you can use a pair of pliers to bend the HDMI back in place. If it’s broken and the terminals and connectors are detached, you can fix it by resoldering. You will need some specialized equipment for this.

The HDMI port on some monitors or other devices can be broken if too much force is applied to them. Before attempting to fix it, check with your warranty information to see if any issues will arise from this endeavor.

How To Fix Broken HDMI Port?

How To Fix Broken HDMI Port

A broken port has several fixes for minor to major ones. While minor issues can be fixed very easily, major issues may require you to replace the broken HDMI port with a new one.

The type of repair depends upon the Type of Damage

If HDMI Port Is Bent:

If the issue faced is a bent HDMI port, then you can follow these steps.

Step 1: Disassembly

This step will depend on the damage done. If it’s just a minor bend, you can handle the fix without having to fully tear down the device. However, if the port has significant damage, you will need to disassemble the device to have a better room to work with.

This is even more so if you have to do some soldering when the port has come off its solder pads.

Step 2: Bending the HDMI Port Back

The most common issue with a damaged HDMI port is that it would bent due to constant plugging in and out of the cable.

The HDMI port, in most cases, is attached to the motherboard of a particular device. To fix it, you have to first ensure that it is firmly connected before you start bending it back.

Furthermore, this fix is only applicable if the HDMI port has a bend on it that prevents you from plugging in other connectors.

These bends occur mostly on the metal part of the port that encloses the inner pins, and it is easy to fix, as opposed to having damaged pins.

Here you’ll need to use the needle nose pliers because it offers a lot of precision. It is also relatively cheap to come by.

Use the pliers to gently bend the bent part back to position. Also, take care not to deform the port while you’re at it as any significant deformation will cause an obstruction that will prevent you from inserting HDMI cables into the port.

Drawbacks and Caution Regarding Bending

There is a high risk of damage with this method, as it involves manually shaping something that was very precisely cut and formed by a machine. A little too much pressure and you may worsen the port.

Also, because the HDMI is connected to a motherboard, ensure you’re not very rough to prevent damages to the board or undoing the solders holding it in place.

If the HDMI Port is Broken Off

If you have an HDMI port that has completely broken off, you can fix it by first dissembling and then soldering.

Soldering Back a Broken HDMI Port

It is also important to know how to fix broken HDMI port with solder issues. This can come about when some of the terminals of the port are not well connected to the motherboard.

Before you carry out this process, physically inspect the board to try and find any noticeable disconnections.

You should also use a multimeter to test the connections. With the device set to carry out a continuity test, touch one probe on a terminal on the HDMI port.

The other end should be placed on the respective solder pad on the motherboard that corresponds to the said terminal.

Listen for a beep, and if you don’t hear one, or if the continuity test fails, you should be looking to do some soldering.

An HDMI port typically has about 19 pins, so this test should be repeated for all the available pins.

Once you’ve found the broken connections, use a soldering iron with a very small tip to carefully resolder the terminals. Take care not to have it overflow and create contact with other parts as this can lead to short circuits later on.

Drawbacks of Soldering

This method relies on the user knowing soldering electrical components. For users without much experience the chances of causing more damage are high.

Also, attempting this fix will very likely void your warranty. So, if your device is still under the warranty protection, it’s best to send it back to the store or the manufacturer to have it fixed or replaced.

If You Want to Replace the Entire Port

If the port is damaged beyond repair, you will have to replace it with a new one. Unlike fixing a few broken connections, here you’ll need to de-solder the old HDMI port, get a new one, and solder that onto the board. Here’s how to fix broken HDMI port by replacing it.

Since they are mostly surface mounted devices, you will need to heat and melt the solder holding the port to the motherboard. Then, remove the HDMI port gently and clean the contacts with some flux, some heat, and solder wick, making sure to remove any traces of the old solder.

Make sure the new port is one that has been tested and does work. You will then have to carefully solder it onto the PCB (Printed Circuit Board).

It’s ideal to have a schematic of the connections for reference at hand. This step is also a bit complicated and error-prone, so it’s not advisable for all users. A qualified technician should be involved when in doubt.

The following video is an example of how to solder a replacement HDMI Port.

Also Read:


A broken HDMI port on a device that you use occasionally is an inconvenience. If you know how to fix broken HDMI port and you have the necessary tools and skills, you can save yourself a lot of time and stress.

Fixing the HDMI port will depend on the extent and kind of problem. Minor breakages and bends can be fixed with a set of pliers.

However, if the problem is more internally based, like a disconnection from the PCB, you may need to do some soldering, with full replacement being the last resort for completely damaged pieces.


Add comment


I am an engineer with a keen interest and a passion for PC builds and hardware. is essentially the culmination of our enthusiasm towards this subject. We review PC peripherals and hardware, talk about custom builds and informative topics regarding troubleshooting issues, understanding a component better and general tips for DIY PC builders.